Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
How do you actually feel on the subject of Tools You Need to Install a New Bathtub ?
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move speedily; if you have to open up a wall to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will need an assistant to leave the old tub as well as embeded in the new one. Make sure you have actually qualified on your own for the work and fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have actually currently purchased a new bathtub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material list should comprise the following:
Getting ready for the Setup
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly come from the pipes. When the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub until the spirit level reviews level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water system and also inspect all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait until the tub has been made use of at the very least once as this will certainly settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines are in place between the faucet as well as the sink. Secure the tap in position with the supplier given backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The former type ought to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a stiff seal, causing the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with dampness and feasible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealant can split relatively very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Write a review below. We would be pleased to find out your thoughts about this entry. Hoping that you visit us again in the future. For those who liked our page if you please don't forget to share it. Bless you for your time. Visit again soon.
No more waits, dial now! Report this page